![clone x gel for softwood clone x gel for softwood](https://cdn.shopify.com/s/files/1/0249/5889/4131/products/image_87061_500x500.jpg)
Successfully rooting clones can become routine if you can control the climate and master your method. You can occasionally mist plants with pure water if the RH gets a bit too low. Try to keep humidity 70-80%+ and temps at 24☌. Maintaining optimal environmental conditions during propagation is critical to clone survival. Clones do most of their actual rooting during the dark cycle. Don’t be tempted to run 24 hours straight to speed things up. 250W is about right for any light system. Powerful lamps are too intense and not needed. Cool white CFL, MH, or LED will do just fine.
![clone x gel for softwood clone x gel for softwood](https://www.aquagardening.com.au/assets/full/130259.jpg)
The ideal habitat for cannabis clones is a propagator under an 18-6 light schedule.
![clone x gel for softwood clone x gel for softwood](https://cdn.mydeal.com.au/44522/clonex-rooting-hormone-gel-purple-for-softwood-and-hardwood-cuttings-yates-50ml-744231_03.jpg)
This is in order to promote root development without building up too many auxins in the medium that will inhibit stem growth later. Other growers will use a light solution to assist rooting by adding a few ml of cloning liquid with watering, directly after transplant. As the plants transition to vegetative growth proper, you need to transplant to a medium with fewer auxins or stem development will be stunted. This is most effective with seedlings in small pots or containers. Some home growers will mix cloning powder with seedling potting mix to make it more auxin-rich. Dunk and pop your clone in a rooting cube.
#Clone x gel for softwood full
You dunk your cutting into a small cup full of gel, only the gel is a gooey consistency and covers more of the cutting base and lower stem. Again, to use gel, it’s more or less the same as the other two methods. CLONING GELĬloning gel is probably the most popular form of rooting hormone used by home growers these days. More common is for growers to dunk a fresh cutting in a lid full of cloning liquid for 5 seconds, and then insert in the rooting medium. Some growers like to dilute a few ml in 6.0pH water and immerse rooting mediums like coco coir, Jiffy pellets, or rockwool cubes in the solution to promote root zone development. CLONING LIQUIDĬloning liquid is pretty versatile. Then, place your cutting in your medium of choice. Most growers fill a bottle cap or small cup and tap off the excess. After you make your cut, you need to cover the tip in powder. As a powder, it has by far the longest shelf-life of any rooting product plus, you can root a lot of clones using little powder. The best way to root clones is the way that works for you, again and again.Ĭloning powder is favoured among commercial growers and those planning on large crops. And practice, practice, practice until you’ve got it down perfect. If you want a high rate of success and a process that you can repeat, you must match the right tools with the right techniques. High-quality cannabis rooting hormones are inexpensive and will cost you less than €20.
![clone x gel for softwood clone x gel for softwood](https://i.ebayimg.com/images/g/R88AAOSwsIFcwsuc/s-l400.jpg)
Using homemade rooting products or those from the garden centre is amateurish and not recommended. Some square gardening products work and some don’t. It’s best to stick with the cannabis-specific brands. You have three types of rooting product to choose from rooting hormone is available in gel, liquid, and powder form. Ok, so you’ve decided on a clean cutting tool, invested in a propagator, and perhaps you have some cutting practice, albeit with mixed results. But without a dose of rooting hormone and a new home inside a propagator, odds are, plenty of your clones are already done for. Sure, you can cut stems at a 45 degree angle with scissors, or cut finely with a razor blade, or cut precisely with a scalpel. But no matter which method you use, the biological fuel for root development are rooting hormones. There is no one way to take cuttings and root them. Expect to take losses and stack up a cutting kill count before you figure it out. To successfully root cannabis cuttings, the grower must be willing to experiment in order to discover the custom formula that works for them. Grower error is responsible for most clone casualties. Although, to be clear from the outset, the number one cause of death for cannabis clones is the cannabis cultivator. Taking cuttings is hit-or-miss for a variety of reasons. Cloning is consistently inconsistent for all kinds of growers, from novices to cultivators with decades of grow room experience.